Jump to content
AUSTRALIAN DJ FORUMS
Sign in to follow this  
yizzle

Building A DVS Timecode DJ Setup For $20

Recommended Posts

kDTNCa4.jpg?1

Many DJs own turntables or CDJs but don’t have the cash to start building out a full setup for control vinyl right away – so how can you test the waters of a DVS system without breaking the bank? Today we’re sharing a tip from a DJTT reader ssamkange on how he built his own DVS setup for less than $7.

Note: The process described below is for experimentation and budget setups – don’t expect to plug in at a club or festival with the low-end sound cards discussed in this article and to be impressed with the results.

What You Will Need:

• Mixx DJ Software: free download

• Timecode: free if you’re burning CDs (Serato), vinyl can be as cheap as $10

• Cheap USB Soundcards: $5 – $8 (you’ll need two)

• Y-Cables: $0 - 5

Total: $10 if you’re good, but maxing at around $30 if you go “all out”.

Cheap Soundcards

Ht6rJ2a.jpg?1

A sampling of the sub-$10 soundcards on the market.

This is the major DJ life hack in this project. Forget everything you’ve ever heard about sound cards – it is possible to get halfway decent audio out of a very low-cost USB soundcards. You also don’t need the most incredible soundcard ever for timecode control. It likely won’t stand up to the test in a club or major festival environment, but to quote ssamkange‘s email:

"[the setup] worked PERFECTLY. I did a proper hour with NO HICCUPS. Took it a step further. Did a house party and the whole night used my $7 DVS and it was all good."

Here’s a few rules for choosing a cheap soundcard:

• Make sure the inputs and outputs are both stereo – mono will not work.

Buy two of the same soundcard – they’ll have consistent clocking, and adjusting the latency settings will have the same result on each one.

Be ready for them to die. Most of these cheap soundcards have a handful of reviews mentioning an untimely demise. They’re cheaply made.

The three cards that we’ve sourced over on Amazon are the iLuv USB Audio Adapter ($9.99), CommonByte USB Sound Card ($3.49), and Virtual 5.1-surround USB 2.0 External Sound Card ($1.90).

Routing The Audio

s7JUUiG.jpg?1

Standard Y-cables: you’ll need four.

In order to get these soundcards to work for your two-channel DVS setup, you’ll need to have four Y-Cables (Stereo RCA to 1/8″). This is two for each soundcard – one from the turntable/CDJ to the stereo line input, and one from the stereo output to your mixer.

luwi3EI.jpg?1

Adjusting latency settings is easy in ASIO4ALL

With the software discussed below, you’re able to route input and output audio across multiple soundcards. However, you may need to adjust the latency of the soundcards – and it’s a lot easier to do this when they’re grouped together. We recommend combining them in ASIO4ALL (PC) or the built in Audio MIDI Setup utility on Mac OS X and adjusting the latency compensation/ Buffer Offset / Buffer Size until the latency is acceptable. Ssamkange found it worked best when reducing the buffer size to 256 samples and using a 44100k sample rate.

Software Selection

F0CIGfg.jpg?1

Perpetually free, Mixxx is the cheapest DJ software option.

The last step of getting this budget rig all working is on the software side of things. Serato and Traktor are out right away as they both require proprietary scratch soundcards. Virtual DJ will work fine, but to unlock timecode control will run $299 for the Pro version. This is where the free Mixxx DJ software is the best option. There’s free timecode control that works with Serato, Traktor, or Mixvibes control signals, and the ability to use multiple soundcards within the software’s settings.

HboMDNM.jpg?1

Routing the audio with the combined ASIO4ALL device

You’ll need to configure the settings to choose the soundcards’ (or combined audio device, if applicable) inputs as the timecode input, and the outputs as the master out (see image above). There’s also a place to adjust what type of time code is being used with the system, and additional latency control within the preferences if you’re still having issues.

* ysm notes:

• I didnt notice the iLuv USB Audio Adapter for $9.99 only has FREE Shipping only on orders over $35

• Software Section: there is a Linux option called xwax that is free

• This is all in USD. So being posted on 05/04/14 the current conversion rate is- 1 US Dollar equals

1.08 Australian Dollar

Source: djtechtools.com

Share this post


Link to post
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

Sign in to follow this  

×
×
  • Create New...